Big Mouth™ Cold Air Induction
The standard system draws warm air from a small opening in the top panel and from a restrictive tube behind the bumper bar.
SS Inductions’ Big Mouth™ system channels cool air from the front of the moving car - from under the bonnet and also from the front grill area by utilising the unique SS Inductions’ aluminium air scoop which attaches to the air-conditioning condenser. This extra airflow is then rammed through the lower and front openings in the induction unit directly to the double entry intake connected to the standard airbox, ensuring maximum delivery of cold air to the motor.
Expect up to 12kW increase at the rear wheels, smoother performance, more responsive throttle and a considerable fuel saving.
The three-part kit consists of plastic induction unit, plastic double entry connecting intake and the unique SS Inductions’ aluminium air scoop. RRP $399.00.
Part # CAI007
Growler Cold Air Induction
The standard system draws warm air from a small opening in the top panel and from a restrictive tube behind the bumper bar. SS Inductions’ Growler system incorporates a streamlined pod style airbox that draws cool air from behind and beneath the headlight and rams it through a superior long-life Big Mouth™ pod filter (manufactured by Kingdragon®, Italy).
Expect up to 16kW increase at rear wheels, smoother performance, more responsive throttle, a considerable fuel saving and a nice induction growl under hard acceleration.
The four-part kit consists of plastic pod-style airbox with lid, plastic replacement front panel and the Big Mouth™ pod filter (which normally retails at $170.00). RRP $599.00.
Part # CAI019
Big Mouth™ High Performance Filter
Manufactured by Kingdragon®, Italy. These long-life washable filters have superior airflow and maximum filtration. RRP $125.00.
Part # PAF002
Big Mouth™ CNC Billet Airflow Meter
The airflow meter basically measures airflow directly, with an electronic sensor on the air stream of the intake providing an output voltage reading that is proportional to the mass air flowing into the engine. The airflow meter then sends the necessary information to the ECU, which recalculates fuel flow and ignition timing.
The SS Inductions’ Big Mouth™ Airflow Meter has a superior flow rate compared to standard and a more streamlined airflow compared to a modified meter. It uses the original centre with the electronic sensors from your standard airflow meter to ensure there are no engine management problems.
The resulting changes to the air/fuel ratio and ignition timing mean a noticeable power gain (up to 12kW at the rear wheels) and a considerable saving in fuel consumption. This is a non-exchange item that enables the original meter to be retained. RRP $445.00.
Part # AFM111
The standard pipe connecting the airflow meter and throttle body is very small in diameter and has inner ridges that disrupt airflow.
The SS Inductions’ intake pipe is a three-piece high volume plastic pipe with flexible rubber ends. The increased air mass ensures improved throttle response while the inner smoothness is less disruptive to the airflow at all speeds. RRP $185.00.
Part # ITP001
Big Mouth™ CNC Billet Throttle Body
The standard throttle body has a 74mm butterfly and is very restrictive.
The SS Inductions’ Big Mouth™ Throttle Body with its 78mm butterfly delivers greater torque and throttle response through the entire rev range. Expect an increase of up to 8kW at the rear wheels.
The kit includes sealed bearings and full fitting instructions detailing how to swap switches, shaft etc over from the standard throttle body. This is a non-exchange item that enables the original throttle body to be retained. RRP $699.00.
Part # PTB000
Dual Engine Covers
Heat retention is a big problem with attaining optimum performance from the LS1 engine. Similar to the covers on the limited edition HSV GTS, the SS Inductions’ dual engine covers not only look great but, just as importantly, prevent that heat build-up. The covers are made from high-heat plastic and feature protective heat shield.
Available in red or black as standard plastic colours or colour-coded to match your car. RRP from $380.00.
Part # DEC001 (red smooth)
Part # DEC002 (black textured)
High Performance Ignition Leads
9mm Spiral Wire gives lower resistance than standard leads hence a stronger spark for better performance and economy. RRP $165.00.
Part # HPL005
This great looking plastic gauge holder is designed to hold two standard sized gauges (2 1/16” and 2 5/8”) and is mounted on the top of the centre dash, pointing toward the driver. It is available in black or gunmetal grey, with a smooth finish. RRP $89.90
Part # DGH004 (gunmetal grey)
Part # DGH005 (matte black)
VY-VZ SS Ute Rear Infill Panel
The plastic infill panel for the VY Ute sits between the rear bumperettes for a one-piece streamlined appearance and to centre the rear number plate. Allows easy access to the spare wheel compartment. The panel is supplied in undercoat for a perfect colour match from your local painter. RRP $275.00.
Part # VUP002
Air Deflector Fins
These Air Deflector Fins adhere to the top of the rear window (sedan only) to give a great sporty look and reduce drag & turbulence at the rear of the vehicle. As a vehicle moves forward the air flowing over the roof becomes separated and turbulent, creating drag. The Air Deflector Fins create a series of vortices smoothing out the airflow and causing it to stick to the back of the vehicle, reducing the total drag. The rear window is left cleaner and drier in wet conditions as there is no longer a vacuum pulling in dirt and water, meaning you have better visibility and clearer rear vision! Manufactured from high grade black ABS plastic in a smooth or textured finish, these Air Deflector Fins may be painted to match your vehicle or left as is. RRP $169.00
Part # ADF003 (smooth) Part # ADF004 (textured)
©2007 launchperformance.com.au ~ Launch Performance™